Cracked, moldy caulk around your tub lets water get behind the wall. Here is how to caulk a bathtub: cut out the old bead, clean and dry the joint, apply fresh sealant, and leave it to cure.
You can find more jobs like this one in our guide to diy home repairs.
| Item | Value |
|---|---|
| Air-dry time after cleaning the joint | At least 30 minutes |
| Angle to cut the nozzle | 45-degree angle |
| Nozzle opening | About 3/16 inch in diameter |
| Widest gap to fill | No wider than a quarter inch |
| Deepest gap to fill | No deeper than a half inch |
| Cure time before regular shower use | At least 24 hours |
These figures come from guides by This Old House and Bob Vila. They can change, so check the source and your product label before you rely on them.
How can you tell the caulk has failed?
A bead that is cracked, peeling or moldy has stopped doing its job. One sealant maker’s guide says that once caulk breaks down, water can reach the smallest gaps and seep behind the wall. Even a narrow split can let moisture in, so it pays to act early.
Check the joint where the tub meets the tile or wall for these signs, as listed by the same guide:
- Cracked, flaking or pulling caulk, which means the seal is starting to break down.
- Discoloration at the edges, often a sign that moisture has lingered.
- A brittle texture: press lightly along the bead, and if it lifts or crumbles, it has failed.
LePage’s guide adds that soap scum, residue, cracks or a brownish tinge mean the caulk has deteriorated and needs to be stripped away.
Choosing between silicone and acrylic latex
Look for tubes labeled for kitchen and bath use. Bob Vila’s guide advises checking the label for a product designated for kitchens and baths. This Old House notes that these caulks are acrylic latex or silicone compounds formulated to resist mildew and stick to smooth, nonporous surfaces.
The two types trade ease of use against durability, according to This Old House:
- Silicone: it is difficult to smooth, needs mineral spirits for cleanup and smells strongly until it dries. It comes in only a few colors, including clear, white and almond.
- Acrylic latex: it is easy to smooth, cleans up with water and has little to no smell. It shrinks more and dries harder than silicone, so it may need replacing sooner, although the replacement is quicker.
Not everyone agrees on which is better. A silicone manufacturer’s guide argues that acrylic shrinks, cracks and fails in wet zones even if it looks fine on day one, so weigh that against the easier handling of acrylic.
What you need before you start
The job needs few tools. One manufacturer’s guide lists the following kit:
- A caulk gun
- Gloves
- Rags or paper towels
- Painter’s tape
- Isopropyl alcohol
- A utility knife for a stubborn or hard-to-lift bead
A gun is worth using over squeezing a tube by hand, since Bob Vila’s guide says it lets you manage the flow better and gives more accurate results. If you are still building your kit, our list of basic tools every homeowner needs is a good place to start.
How to remove old caulk
Removal is the slow part, and it decides how well the new bead holds. Work through the joint in this order:
- Cover the tub with a drop cloth so scratches and debris stay off the surface, as This Old House recommends.
- Cut through the old bead with a utility knife or razor scraper, keeping the blade at a low angle so it does not damage the tub or tile.
- For stubborn silicone, cut into the center of the bead, grip the cut end with needle-nose pliers and try to pull the whole strip out in one piece.
- Scrape away leftover residue. Surfaces previously sealed with silicone should be scrubbed with an abrasive pad soaked in mineral spirits.
- Wipe the joint with rubbing alcohol, then dry it with a clean rag or paper towel.
- Let the joint air dry for at least 30 minutes before you apply new caulk.
If you find mold, Bob Vila’s guide suggests a commercial cleaner or a homemade solution of one part bleach to two parts water. LePage suggests a cloth dampened with bleach or a non-ammoniated cleaner, followed by a warm-water rinse.
The same LePage guide says to wear protective gloves and work in a well-ventilated area whenever you use chemical substances. Let every surface dry completely before you move on.

How to caulk a bathtub with fresh sealant
Check the size of the gap first. Bob Vila’s guide says the gaps you seal should be no deeper than a half inch and no wider than a quarter inch. Then follow these steps:
- Tape the lines. One sealant guide places painter’s tape about 1/8 inch from each side of the joint and presses it down firmly so no sealant seeps underneath.
- Prepare the gun. Cut the nozzle at a 45-degree angle, leaving an opening of about 3/16 inch in diameter, then pierce the inner seal with the gun’s wire tool, as This Old House describes. Squeeze lightly to check that the caulk flows smoothly.
- Lay the bead. Keep even pressure and try not to stop mid-line, advises the same guide.
- Smooth it. Wet your finger and wipe along the line to remove excess and leave a rounded bead, as Bob Vila’s guide explains. LePage describes the goal as a neat, concave shape.
- Pull the tape. Peel it off while the caulk is still wet, then move on to the next section.
Move quickly on the smoothing step. The sealant guide quoted above says to shape the bead before it starts to skin, which happens within a few minutes.
Curing time and keeping the seal mold-free
Guides disagree on how long to stay out of the tub, so the product label is the final word. Here is what the three main sources say:
- Bob Vila’s guide: allow the caulk to cure for at least 24 hours before regular shower use.
- One silicone maker: its product is water-ready in 30 minutes, but the seal should not be touched or exposed for 24 hours.
- LePage: most caulking needs 48 hours for a fully cured seal, so check the instructions for your sealant.
A little upkeep helps the new bead last. The silicone maker’s guide suggests these habits:
- Run the fan or open a window after showers to clear out moisture.
- Wipe the sealant line dry, especially in corners and along the tub base where water collects.
- Check the seal once a year for cracks or lifting that could let water in.
While you are tackling bathroom jobs, our guide on how to fix a running toilet covers another common repair.
Frequently asked questions
Can I put new caulk over the old bead?
Show answer
Usually not. Bob Vila’s guide says that caulking over old caulk won’t give optimal results, so strip the joint first.
Is grout a good substitute for caulk where the tub meets the wall?
Show answer
LePage says cement-based grout is less flexible than silicone, acrylic or latex caulk and more prone to cracking over time. A flexible sealant suits a joint that moves.
Which caulk suits a fiberglass or ceramic tub?
Show answer
According to LePage, silicone is usually best for fiberglass tubs, while acrylic latex is recommended for ceramic ones. Read your tub maker’s and sealant maker’s instructions to confirm.
What should I use if my tub or surround is plastic?
Show answer
This Old House advises a plastic razor blade, since metal blades can scratch plastic or acrylic. It also warns that chemical caulk removers can harm plastic surfaces.
